OneLaser X-Series (XT & XRF) Setup Guide¶
I run an XRF in my own shop every day: tumblers, hat patches, cutting boards and award plaques. This is how I'd set up an X-Series from the crate. It combines OneLaser's official instructions with what I've learned running mine.
Both machines are CO₂ lasers (10.6 µm) on a gantry. The difference is the laser source:
- OneLaser XT: a 55 W glass tube, cooled by a small built-in water tank and pump.
- OneLaser XRF: a 38 W RF metal tube that's air-cooled. There's no water, so cold or hot shop temperatures are much less of a worry.
At a glance¶
| Spec | XT | XRF | Source |
|---|---|---|---|
| Laser source | 55 W CO₂ glass tube | 38 W CO₂ RF metal tube (rated up to 30,000 h) | Product pages / manual |
| Cooling | Built-in water tank and pump | Air-cooled, no chiller | Product pages / manual |
| Work area | 23.6″ × 11.8″. Enter 600 × 300 mm in LightBurn | 24″ × 12″ (610 × 305 mm). Enter 600 × 300 mm in LightBurn | Product pages / OneLaser Wiki |
| Machine size (L×W×H) | 43.2″ × 28.5″ × 10.5″ | 43.2″ × 28.5″ × 10.5″ | Product pages |
| Weight | 119 lb (54 kg) | 127–128 lb (58 kg). My XRF plus riser base came in at 235 lb crated | Product pages / my unboxing |
| Max speed / accel | 1,000 mm/s, 3G | 1,200 mm/s, 3G | Product pages |
| Exhaust | 3.94″ (≈100 mm) port. Fan and duct included | Same | Spec table / my unboxing |
| Air assist | Built-in pump; optional Smart Air Assist | Same | Manual / product pages |
| Power | 100–240 V single phase, set at the factory to 115 V or 230 V; ≈384 W at 115 V | Same; ≈670 W at 115 V. My XRF's label reads 4 A full-load current at 110 V | Manual / XRF page / my unboxing |
| Room conditions | 59–95 °F (15–35 °C), 40–70 % RH non-condensing | Same | Manual |
| Software | LightBurn, RDWorks | LightBurn, RDWorks, MakerBoost AI | Product pages |
| Connection | USB, Wi-Fi, Ethernet (Ruida controller) | Same | OneLaser Wiki |
| Origin | Rear left | Rear left | OneLaser Wiki |
| Laser safety class | Conflicting: manual says Class 2, XRF product page says "Class 1 design" | Same | Manual vs. XRF page |
X-Series setup at a glance¶
| Step | XT | XRF |
|---|---|---|
| 1. Install the tube | Skip. The tube ships installed | Skip. Sealed RF source |
| 2. Cooling | Fill the internal tank (details below) | Skip |
| 3. Inline fan | Mount the included fan on the back port. Don't remove or modify anything internal; OneLaser voids the warranty for that | Same |
| 4. Lens orientation | Check it. Curved side up, flat side toward the material | Same |
| 5. Bed tram | Mostly handled by autofocus. Spot-check if engraves fade across the bed | Same |
| 6. Power on | No key or mA dial in OneLaser's steps. Close the lid, switch on, let it home | Same |
| 7. Mirror alignment | Comes aligned from the factory. Check before you adjust (see below) | Same |
| 8. Clean optics | Use OneLaser's cleaning solution or absolute ethanol. OneLaser says not to use IPA on X-Series optics | Same |
| 9–10. LightBurn | Ruida, 600 × 300 mm, origin rear left | Same |
| 11. Back up settings | Same as any Ruida machine | Same |
| 12. Focus test | Autofocus, then verify | Same |
| 13. Test cards | Same idea. OneLaser also publishes starting parameters | Same |
Step by step¶
1. Unbox and place it¶
These steps follow OneLaser's unboxing guide:
- Cut the straps and lift off the crate top and sides.
- Pull the foam and film, and check the tool bag against OneLaser's included-parts list.
Plan the move. My XRF and riser base together weighed 235 lb crated. The machine alone is 120–130 lb, so it's a two-person lift onto a solid bench.
What was in my box: the inline fan and ducting, cleaning supplies, power, USB and Ethernet cables, and a thumb drive.
2. XT only: fill the cooling tank¶
OneLaser ships the XT with the tank drained. If you power it on dry, you can cause an electrical failure. This follows OneLaser's water tank guide:
- Remove the back cover and left door with an M2 hex key.
- Pour about 790 ml of distilled or purified water into the tank. Use only distilled or purified water.
- Power on and let the pump pull water into the tube.
- Top off with about 150 ml more, then cap it and reinstall the covers.
- Newer XTs have a water-level sensor that stops the pump from running dry.
Temperature: OneLaser wants the coolant at 15–25 °C, and its cooling and freeze guide is clear that freeze damage isn't covered by the warranty.
Antifreeze: if the room drops below about 10 °C (50 °F), use one of OneLaser's approved antifreezes at their ratio. The starting point is 3 parts antifreeze to 7 parts water, which protects to roughly −12 to −15 °C. - Add the water first, then the antifreeze. - Change it every 2–3 months. - Don't mix brands.
Storage: drain everything if the machine will sit unused for a long time.
3. Exhaust¶
Fitting the fan: remove the plate on the back, connect the fan's 24 V plug, screw the fan onto the port, and attach the duct. On mine it's a straight shot out the back.
Where to vent: outside is best. If you can't vent outside, OneLaser shows how to connect their air purifier.
Upgrading the fan: OneLaser's exhaust troubleshooting page gives a target spec for X-Series fans: - about 366 m³/h (≈215 CFM) - 578 Pa static pressure - about 3,800 RPM
The AC Infinity CLOUDLINE S6 is a solid choice. It's a 6″ fan, so you'll need a 4″→6″ adapter.
Fan placement: OneLaser's advice is that on flexible duct, the fan goes close to the machine, and on rigid pipe it can sit at the far end. Inline fans do pull better than they push, so on a long rigid run I'd put mine near the outlet.
Smoke leaking out? OneLaser says it's an airflow balance problem. Either the air assist isn't feeding enough fresh air in, or the exhaust fan is too weak. A stronger fan plus a compressor for air assist fixes most cases.
4. Power¶
- Plug into a grounded outlet that matches the voltage on the rear label (115 V in the US).
- Close all covers, switch on, and let it home.
- Don't press ESC while it homes.
Circuit: my XRF's label says 4 A full-load current, so a normal 15 A household circuit handles the laser itself.
5. Connect LightBurn¶
These settings follow OneLaser's USB, Ethernet and Wi-Fi guides.
USB: install the LightBurn trial along with its USB driver. Then add a device: - choose Ruida, then Serial/USB - enter a work area of 600 × 300 mm - set the origin to Rear Left
Ethernet: this one isn't plug-and-play, and "Find My Laser" won't find it. 1. Give your computer the static IP 192.168.1.30, subnet 255.255.255.0. 2. In LightBurn, choose Ruida, then Ethernet/UDP, and enter the laser's default IP, 192.168.1.100.
Scanning offsets: your machine ships with scanning-offset values (OneLaser also calls them reverse compensation). Enter them in LightBurn so bidirectional engraving lines up. OneLaser has a tuning guide for them.
Back up your machine settings before you change anything: Edit → Machine Settings → Save.
Camera tip from my setup video: for the LightBurn lens calibration, you don't need the card flat on the bed. Open the lid and hold the card up where it matches the preview. That's much easier. For the camera alignment step, put tape on the bed, focus on it, and run the target pattern at low power.
6. Check alignment (don't just start turning knobs)¶
OneLaser aligns these at the factory. Their light-path guide warns that once you loosen a mirror knob, getting it back can take four hours or more. So check first.
How I check: 1. Put masking tape over the nozzle. Ignore the red dot, because it's independent of the beam. 2. Pulse once with the head at the back left, closest to the tube. 3. Move to the front right, farthest from the tube, and pulse again. 4. If the two marks land on top of each other, leave it alone.
Mirror tip: the X-Series mirrors slide out after you loosen a thumb screw. When you put them back, snug the screw finger-tight, not cranked down.
7. Focus¶
Autofocus handles most jobs.
Manual focus: on mine, the focal distance is about 10 mm from the nozzle tip with the stock lens. I keep a step gauge on hand to set it by hand.
Testing focus: OneLaser has a dot test for finding focal length if you want to confirm the right number for your lens. A ramp test works too.
Changing lenses: if you swap to the optional 2″ lens, read OneLaser's note on installing a 2.5″ lens in the 2″ position. Getting it wrong causes a hidden misalignment.
8. Air assist¶
Stock air: the built-in pump is fine for engraving.
For clean cuts: feed it from a shop compressor. OneLaser shows how to connect an external blower. Pull the built-in line off the blue valve and push your compressor line in.
Upgrades: the OneLaser Air Assist Control switches automatically between low air for engraving and high air for cutting. I've also installed a Liberty Controls kit on my XRF: video.
Compressor gear: see Gear we use for the regulator and hose I run.
9. Maintenance rhythm¶
This is OneLaser's recommended rhythm from their maintenance guide:
| How often | What to clean or check |
|---|---|
| Daily | Lens, auto-focus sensor |
| Weekly | Mirrors 2 and 3, work table, cooling fan, beam combiner |
| Every 3 months | Mirror 1, exhaust fan, the XT's water tank, vent slots |
| Every 6 months | Belts, bearings and rails |
| Yearly | Whole machine |
Cleaners: use OneLaser's cleaning solution or absolute ethanol on the optics.
Guide wheels: I made a video on replacing worn guide wheels on the XRF.
10. First job¶
- Run test cards.
- Start from OneLaser's published starting parameters: 38 W RF or 55 W glass.
- Use the finding your settings method to dial it in.
My acrylic tips video was shot on the XRF.
Home setup checklist¶
- Bench: solid and big enough for 43″ × 29″ and about 130 lb, with room behind for the duct and cord.
- Exhaust: included fan on the 4″ port, vented outside. Upgrade to OneLaser's fan spec if smoke escapes. See Ventilation and safety.
- Power: grounded outlet that matches the label voltage. A normal circuit is fine.
- Cooling: XT gets distilled water, plus approved antifreeze below 10 °C. XRF needs nothing.
- Air: stock pump to start, compressor for cutting.
- Safety: CO₂ extinguisher nearby, never run unattended, don't defeat the lid interlock. See Laser eye safety and fire.
Still unknown / confirm with OneLaser¶
- Laser class: the manual says Class 2, the XRF product page says Class 1.
- XT current draw: the manual lists 383.5 W. I haven't confirmed the label amperage on an XT.
Sources and more videos¶
OneLaser: - X Series Wiki - X Series User Manual (2025, PDF)
My videos: - OneLaser XRF Unboxing - X Series Camera Setup - X Series Beam Alignment - XT/XRF Liberty Controls air assist install - XRF guide wheel replacement - XRF vs xTool P2 - Best laser for your small business
Accessories: Riser Base
Buying an X-Series? Use my partner link 1laser.com/BEARDEDBUILDS and code BEARDEDBUILDS. Then learn the software properly with Master LightBurn.
Disclosure
Bearded Builds Co is a OneLaser partner. OneLaser links include my referral, and I may earn a commission at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. OneLaser Wiki content is summarized in my own words and linked as the source.